Media sensor optionsProduct: T5000rSymptomWhat are the media sensor options, and how is top-of-form sensed with different media types?Possible CauseThe media sensor options are set in the Gap/Mark Sensor submenu of CALIBRATE CTRL.Recommend SolutionThe following options are available in the menu CALIBRATE CTRL under “Gap/Mark Sensor “:Gap: detects die-cut labels on liner media, and notches and holes in tag stock.Mark: senses a black mark on the underside of tag or label stock.Advanced Gap: detects liner gaps between die cut labels having a dark background.Advanced Notch: detects notches or holes that interrupt a dark or black area on the underside of the media.Disable: senses no label indicators and ignores all existing label length indicators on the installedmedia.Align the lower media sensor as described below for each Gap/Mark Sensor value. Align the upper media sensor with the lower media sensor, either to provide a consistent background or to use in conjunction with Advanced Gap or Advanced Notch.Gap: position lower sensor where it is out of the path of preprinted areas and clear of fringe effects from the corner or edge of a label. If media is gapped and contains a hole or notch, move the sensor out of the path of any holes or notches. If non-gapped media has a notch or hole, position sensor to pass through the center of the notch or hole.Mark: position lower sensor to pass through the center of the black mark, out of the path of preprinted areas.Advanced Gap: position lower sensor where it is out of the path of preprinted areas and clear of fringe effects from the edge of a label. The upper sensor must be positioned above the lower sensor.Advanced Notch: position lower sensor to pass through the center of the notch or hole, out of the path of preprinted areas. The upper sensor must be positioned above the lower sensor.Disable: the lower and upper sensors are not used.

ZGL commands ~HS or ~JA do not return statusProduct: T5000r and T4MSymptomZGL commands ~HS or ~JA do not return status.Possible CausePrinter configuration, especially if host can communicate other data to the printer. These commands are “preparser” commands, which must be pulled out of the input communications buffer and parsed immediately. Since this adds some overhead to the processing of the input data, it is disabled by default.Recommend SolutionSet the return status port in menu PRINTER CONTROL (T5000r) or PRINTER SETUP (T4M).Note the value of ‘Admin User’.Set ‘Admin User’ to “Enabled” if it is not currently enabled.Set ‘Ret. Status Port’ to the port for ~HS and ~JA to send the status data back to the Host. The default is “Automatic”. Other choices are Serial, E-NET Stat Port, USB, IEEE 1284, Disable, and E-NET Data Port.Return ‘Admin User’ to the pre-existing value.Set the preparser command parameters in the menu ZGL SETUP.Set ‘Preparser Command’ to “HS”, “JA” or “HS and JA” as desired. The default is “HS”.Set ‘Preparser Port’ to the communications channel that will carry the ~HS or ~JA command tothe host: “Ethernet”, “Parallel” or “Serial”. The default is “Disable”.Save the new configuration.Make all other necessary communications settings (baud rate, etc.).Troubleshoot communications problems if ~HS or ~JA still does not return data.

Residue buildup on print headProduct: T5XXX SERIESSymptomHow to obtain optimum life from the print head and maintain good print qualityPossible CauseResidue buildup on print headRecommend SolutionThe Print head has an approximate life of one million linear inches as a Direct print, and two million linear inches with a Ribbon in use. Under normal circumstances the Print Head is a ‘Consumable’ supply product and the customer purchases and replaces them as needed just as media stock and Ribbons would be replaced.With your printer comes a ‘Print head Cleaner Pen’ (To re-order use part# 203502-002). This should be used to wipe off ribbon or other residue that can collect on the print head and cause premature wear or print quality issues. You should perform this after each roll of ribbon and after each roll of label.In addition, the ‘Platen Roller’ should be cleaned as well and inspected for wear. The roller can get a buildup of label glue residue which causes label jams or poor printing. If the roller has “high and low” spots on it from wear, it should be replaced.You can clean the roller with soft cloth and alcohol.

Support for Intelligent Mail Barcode in ZGLProduct: T5000r, T4MSymptomNeed support for IMB (Intelligent Mail Barcode) in ZGL.Possible CauseIMB support in ZGL is not available in T5000r and T4M builds dated before 5/29/09.Recommend SolutionSupport for IMB is provided for ZGL in T5000r releases starting with v1.26R (370190), and T4M releases starting with v1.14G (370186), dated 5/29/09.IMB is a two-dimensional barcode. The bars all have the same width, and the bars are spaced evenly at a density of 22 ± 2 bars per inch. The bars all have a central region, and can extend above and/or below the central region, for a total of four different possible types of bar. Every IMB is 65 bars wide, regardless of the amount of data encoded. The data is a 20 character tracking number and an optional routing number (ZIP code) of 5 or 9 or 11 digits. The total number of data characters must be 20 or 25 or 29 or 31.IMB is supported by ZGL as a variant of the POSTNET barcode. An additional parameter of type was added to the POSTNET (^BZ) definition. The command is now:^BZo,h,,,to=orientation (Normal, Rotated 90° clockwise, Inverted, Bottom-up)h= height (in dots)t = Postal code typeAccepted Values:0 = Postnet barcode (Default Value)1 = Planet barbcode2 = Reserved3 = Intelligent Mail barcode, or “IMB”Use the ^BYw,r,h command to set width of x-dimension and overall barcode height:Key specification tolerances:Overall barcode length between 2.667 and 3.225 inches.For 203 dpi printers, make the x-dimension width 4 dots.For 300 and 305 dpi printers, make the x-dimension width 6 dots.The ratio parameter of ^BY has no effect for IMB.Overall barcode height between 0.125 and 0.165 inch (height of tallest bar).Height parameter is 26 to 33 dots at 203 dpi.Height parameter is 38 to 49 dots at 300 dpi.Height parameter is 39 to 50 dots at 305 dpi.When positioning barcodes, note that vertical barcode clearance is at least 0.028 inch and horizontal barcode clearance is at least 0.125 inch.SAMPLE PROGRAM (at 203 dpi):^XA ^LL1219FAQ Problem/SolutionFor “Learn from the Experts” section on the Printronix Public Website^FO100,250^A0N,65,65^FD Sample IMB at 203 dpi^FS^BY4,,26^FO100,350^BZ,,,,3^FD00123123456123456789^FS^FO100,480^A0N,30,30^FDTracking number:01 234 567094 987654321^FS^FO100,510^A0N,30,30^FDRouting number: 01234567891^FS^BY4,,33^FO100,570^BZ,,,,3^FD0123456709498765432101234567891^FS^XZ

Media GuidelinesProduct: T5000rSymptomWhat types of media can be used on the T5000r? What is the range of core diameters and maximum roll diameter allowed?Possible CauseUse the following media guidelines.Recommend SolutionType: Roll-fed, die-cut continuous or fanfold labels, tags or tickets; consisting of most direct thermal or thermal transfer materials.Supply Roll: 8 inch (203 mm) maximum diameter on 1.5-inch (37.5 mm) to 3-inch (76 mm) diameter cores.Internal Rewinder: Accepts up to a 5-inch diameter roll of label backing.IMPORTANT: The rewinder supports a maximum diameter of 5 inches. The rewinder is designed to support the full amount of liner from a standard 8 inch diameter media roll. If rewinding the labels and liner both, the maximum diameter roll that should be used is 5 inches.Exceeding this 5 inch diameter limit can cause the liner to rub on the bottom pan.Label Material, Thermal Transfer: Plain-coated papers, vinyl, Mylar, metalized paper, non-woven fabric, fine woven fabricLabel Material, Direct Thermal: visible-light scannable paper, infrared scannable paper, thermal ticket/tag stock, thermally-sensitive plastic stock.

New configuration location of diagnostic messages (T5r)Product: T5rSymptomNew configuration location for user control of diagnostic messages on the T5r.Possible CauseVersions prior to v1.25H p/n 369895 and 369896 had this option in a different location, and it had a different name.Recommend SolutionThe T5000r/SL5000r can return diagnostic and error messages to the user, to help in troubleshooting problems with programming.All the error message controls are placed in a common location, in the PRINTER CONTROL menu, as the ‘xxx Diagnostics’ submenu where ‘xxx’ is the name of the language. For example, if ‘ZGL’ is the selected emulation, then ‘ZGL Diagnostics’will be the name of the diagnostics submenu, and so on.Most of the PPI emulations have just three options:Disable – Will not log errors.Print – Prints the labels with best results and prints the errors on a separate label.Debug Port – Prints the label, and sends the errors to the Debug port.The ‘PGL Diagnostics’ submenu has these options:On – Full error checking reported. Any element such as alpha, line, barcode, etc., that falls off the current page is reported as an error.Debug Mode – Puts the printer in debug mode whenever a form is defined in CREATE mode. Each line of the CREATE form will be printed along with an error if one has occurred.Fault – After an error, the printer prints the error message and halts with a message in the LCD. Operator intervention is required to restart printing.Host – Full error checking reported. Error messages are sent back to the host through the port based on the menu “Ret. Status Port” instead of being printed on paper.Off – There is no error checking. Graphic elements such as alpha, line, barcode, etc., will be clipped if they are beyond the page boundaries.The ‘VGL Diagnostics’ submenu has these options:Enable All – Full error checking and report.Disable – No error checking and report.Error Msgs – Command syntax is checked and error messages printed when command parameters are incorrect.Error Markers – Prints the following error markers for those elements that print beyond the page boundaries:>> for elements that begin off the right side of the page.<< for elements that begin at the indicated position but end off the page.♦ for elements where the starting position of the command contains an error other than an off-page error.Offpage Errors – Reports errors for elements that start or end beyond the right edge of the page.Barcode Errors – An error message will print when invalid barcode data is encountered.

How to center- or right-justify text in PGLProduct: T5rSymptomHow to center- or right-justify text in PGLPossible CauseNew program file version 1.25H (p/n 369895 or 369896) for the T5000r/SL5000r allows a new parameter to the ALPHA command which can center- or right-justify ALPHA fields.Recommend SolutionBy default, the ALPHA command will left-justify text in its field. In other words, the ‘start column’ parameter in the ALPHA command is the horizontal position of the left end of the text.Two new parameters are available: RJUST or CJUST.If RJUST is used, then the start column is the position of the right end of the text.If CJUST is used, then the start column is the position of the center of the text.If neither is used, then left-justification is assumed, and the start column is the position of the left end of the text.RJUST and CJUST can take an additional optional parameter, NLZ, which suppresses any leading zeros in the text.The syntax looks like this:ALPHA[R;][E;][Cn;][AFn;L;][T;]RJUST; or CJUST;][NLZ;[DIR;]…SR; SC; VE; HESTOPNOTE: This feature only works with the scalable fonts that come with the printer. These show up in the font list with a .sf extension, such as 93779.sf or 92500.sf. Also, the feature only works when VE and HE represent integer multiples of character size, so it will not work with the POINT parameter.EXAMPLE:~CREATE;JUSTIFY;144// Application is 4″ by 2″ nametagSCALE;DOT;100;100// typeface is CG Times 92500.sfFONT;FACE 92500ALPHAAF10;18;T;CJUST;110;205;4;3AF20;32;T;CJUST;160;205;2;2STOPEND~EXECUTE;JUSTIFY~AF10;”L. Frank Baum”~AF20;”Famous Author (Children’s Books)”~NORMAL~EXECUTE;JUSTIFY~AF10;”Arthur Clarke”~AF20;”Famous Author (Science Fiction)”~NORMAL

GAP NOT DETECTED error in displayProduct: T5000rSymptomGAP NOT DETECTED error in display.Possible CauseDirty media sensors, wrong label lengthRecommend SolutionClean the upper and lower media sensors by spraying them with dry air. This should bedone every time the media (label stock) is changed.Before running the Auto-Calibrate operation, check the QUICK SETUP or MEDIA CONTROL menu for the ‘Label Length’ parameter. It should be set to the length of the label, not counting the gap.Check that the sensor type has been set in CALIBRATE CTRL menu to match the media and ribbon.”Gap” Select when using media with a liner space between die-cut labels or when using tag stock with notches or holes as label length indicators.”Mark” Select when using media that has horizontal black marks located on the underside of the label liner or tag stock.”Advanced Gap” Select when media is gapped but also has a dark background.This sensor arrangement looks through the ribbon, and will not work if ribbon is too dark.”Advanced Notch” Select when media has a notch that is placed in a dark line on the back of the stock.Check the position of the media sensor. It should pass through the center of gaps or marks or notches, but not through pre-printed areas if possible.Run Auto-Calibrate in CALIBRATE CTRL menu, which sets Gap and Paper Out Thresholds

New configuration location of diagnostic messages (T4M)Product: T4MSymptomNew configuration location for user control of diagnostic messages on the T4M.Possible CauseVersions prior to v1.10P p/n 369675 had this option in a different location, and it had a different name.Recommend SolutionThe T4M/SL4M can return diagnostic and error messages to the user, to help in troubleshooting problems with programming.All the error message controls are placed in a common location, in the EMULATION menu, as the ‘xxx Diagnostics’ submenu where ‘xxx’ is the name of the language. For example, if ‘ZGL’ is the selected emulation, then ‘ZGL Diagnostics’ will be the name ofthe diagnostics submenu, and so on.Any emulation except ‘PGL’ has three options for the ‘xxx Diagnostics’ submenu:Disable – Will not log errors.Print – Prints the labels with best results and prints the errors on a separate label.Debug Port – Prints the label, and sends the errors to the Debug port.The ‘PGL Diagnostics’ submenu has these options:On – Full error checking reported. Any element such as alpha, line, barcode, etc., that falls off the current page is reported as an error.Debug – Puts the printer in debug mode whenever a form is defined in CREATE mode. Each line of the CREATE form will be printed along with an error if one has occurred.Fault – After an error, the printer prints the error message and halts with a message in the LCD. Operator intervention is required to restart printing.Host – Full error checking reported. Error messages are sent back to the host through the port based on the menu “Ret. Status Port” instead of being printed on paper.Off – There is no error checking. Graphic elements such as alpha, line, barcode, etc., will be clipped if they are beyond the page boundaries.

VGL application does not print correctlyProduct: T5r, P7000, L5XXXSymptomVGL application does not print correctlyPossible CauseConfiguration settingsRecommend SolutionVerify that VGL is loaded in the printer, and that VGL is the active IGP emulation(If a P7000 config shows VGL as an enabled feature but “VGL” cannot be set as the Active IGP Emulation, reflash the printer.)Print a hex dump of your job, and verify that the VGL Trigger Character (or ‘SFCC’) is correct. The default VGL SFCC is the caret: ‘ ^ ‘. In a hex dump it has a value of 5E, or 94 decimal. Note that some printers need the SFCC value entered in hex and some in decimal.”Hex” is base-16 numbering, meaning hex: 5E is decimal: (5×16) + (14×1). The ‘E’ is a number in hex because you need 16 digits to count: {0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F}.The SFCC is found in front of all VGL commands, such as ^PY which occurs once at the beginning of graphics and ^PN which occurs once at the end of graphics. Other common commands are ^M and ^T.Another common SFCC on mini/mainframe systems is the logical not, ‘ ¬ ‘ which is usually translated as AA or AC in a hex dump, equal to 170 or 172 decimal. It doesn’t matter what the character looks like on the host, only what it looks like as it enters theprinter.Another common problem with VGL is stray NULL characters in front of the graphics start command. If you are still having trouble, or a hex dump shows anything other than a line feed (hex 0A) in front of the start of graphics command ^PY, enable the option ‘Midline ^PY’ in IGP/VGL SETUP.If you are having a problem with line spacing between forms due to line feeds beingsent by the host computer, some printers have an option called ‘Absorb After ^PN’ which will take out one line feed if enabled.

Prints garbage characters %-12345 at beginning of jobProduct: T4M/SL4M or T5000r/SL5000rSymptomPrints garbage characters “%-12345X” at beginning of job.Possible CausePrinter is not configured for PJL sequence.Recommend SolutionPossibility 1: Legitimate PJL commands are being sent to a printer which is not configured to understand them.Solution 1: T4M/SL4M printers starting with 368490 v1.04K support PJL through an optional Memory Cartridge. T5000r/SL5000r printers starting with 368540 v1.18J support PJL through a menu selection in the standard software.Check the printer configuration of a T4M/SL4M or T5000r/SL5000r to see if a firmware upgrade or hardware option is required.The menu option is called ‘PJL Control’. It must be enabled to allow the printer to parse PJL strings. In the T4M, enable the ‘Admin User’ option then ‘PJL Control’ in the PRINTER SETUP menu. In the T5000r printer, enable the ‘Admin User’ option then ‘PJL Control’ in the PRINTER CONTROL menu.(Earlier T5000/T5000e models cannot be configured to recognize PJL. The commands must be blocked at the host to prevent them from printing out.)Possibility 2: The printer is installed in an Ethernet network, but is connected to a Hewlett-Packard print server such as a JetDirect unit through a parallel cable, and the print server is configured for a laser printer.Solution 2: Consult the print server documentation, and configure the print server for an ASCII or Centronics interface. That will keep the print server from sending PJL commands.

My ribbon take-up just stopped turningProduct: T5, T5e, SL5e,T5rSymptomMy ribbon take-up just stopped turningPossible CauseAn interruption of electrical current between the Ribbon Take-Up Motor and the Controller.Recommend SolutionTake the printer off-line and unlock the ENTER switch.Press the MENU    key until the display reads QUICK SETUP.Press the Down ▼ Arrow key until the display reads PRINT MODE.Press the + or – Key until the display reads DIRECT and press ENTER.Press the DOWN ▼ Arrow Key until the display reads SAVE CONFIGPress the + or – Key to until the desired Configuration option is displayed then press ENTER.Press the DOWN ▼ ARROW Key  until the display reads Power-Up ConfigPress the + or – Key until the Configuration option displayed matches the SAVE CONFIG Configuration option then press ENTER.Power the printer OFF and wait 30 seconds. Then power ON.Now repeat Step 1 to 6, in Step # 4 change the PRINT MODE option back to TRANSFER.When you change the PRINT MODE option back to TRANSFER and press ENTER the printer ribbon motors will turn, the ribbon will tighten eliminating any slack.If the ribbon does not tighten then you will need to have the printer serviced.To obtain service please call Printronix Technical Support or email us at support@printronixautoid.com

How can I get my label to print correctly?Product:  T5, T5e, T5r, SL5e, SL5r, T4M, SL4MSymptomHow can I get my label to print correctly?Possible CauseImproper media loadingPrinter not setup correctlyRecommend SolutionT5, T5e, T5r, SL5e, SL5rTo insure that your media is correctly loaded, follow the threading diagram on the inside of your printer’s cover.For additional details on loading your media please refer to the appropriate User’s Manual.To confirm that your printer is setup correctly:Be sure the printer is initialized, the media is loaded, the printer is offline, Enter key is unlocked. (Press the Down ↓ and Enter Keys together once and release)Press the “Menu” key until the display reads “Quick Setup” or “Media Control”Press the Down ↓ Arrow Key until the display reads “Label Length” (Please measure with a ruler if unknown)If the Label Length is incorrect change using the “+” or “-“ key, then Press the Enter key to save.Press the Down ↓ Arrow key until the display reads “Label Width” (Please measure with a ruler if unknown)If the Label Width is incorrect change using the “+” or “-“ key, then Press the Enter key to save.Press the Down ↓ Arrow key until the display reads “Gap Mark Sense”If the Gap Mark Sense is incorrect change using the “+” or “-“ key, then press the Enter key to Save.(Gap or Mark are used most frequently)Press the Down ↓ Arrow key until the display reads “Calibrate/Run Calibrate”  Please Press the Enter key to run.When completed the display will read “Sensed Distance X.XX” (e.g. 2.11 inches)Confirm that the Sensed Distance is correct.(The Sensed Distance is measured from the top of one label to the top of the next label, includes the gap)If the Sensed Distance is incorrect then re-load the media and run the calibration again.If the sensed Distance is still incorrect then contact printronix Technical Support.Press the Down ↓ Arrow Key until the display reads “Save Config”Please select the desired Config number (1-8 Possible Configurations), Press the Enter Key to save.Press the Down ↓ Arrow Key until the display reads “Power-Up Config”If the Power-Up Config number matches the Save Config number then Press the Enter Key to save.If the Power-Up Config number does not match the Save Config number then using the “+”Or “-“key, then Press the Enter key to save.Power Off the printer, wait 30 seconds then power the printer back on.Print the internal checkerboard test.If the checkerboard pattern prints correctly and does not print in the gap then print your label job again and confirm it prints correctly.If you have confirmed that your printer driver is correct, but your label still prints incorrectly then contact your Label Software Manufacturer.Recommend Solution:T4M, SL4MTo insure that your media is correctly loaded, follow the threading diagram on the inside of your printer’s cover.For additional details on loading your media please refer to the SL4M/T4M User’s Manual.To confirm that your printer is setup correctly:Be sure the printer is initialized, the media is loaded, the printer is offline, Enter key is  unlocked. (Press the Down ↓ and Enter Keys together once and release)Press the “Menu”  Key until the display reads “Media Setup” and then Press Enter.Press the Down ↓ Arrow Key until the display reads “Label Length” (Please measure with a ruler if unknown)If the Label Length is incorrect change using the “Left” or “Right “ key, then Press the Enter key to save.Press the Down ↓ Arrow key until the display reads “Label Width” (Please measure with a ruler if unknown)If the Label Width is incorrect change using the “Left” or “Right“ key, then Press the Enter key to save.Press the “Menu”  Key until the display reads “Sensor Setup” and then Press Enter.Press the Down Arrow ↓ Key until the display reads “Gap/Mark Sensor”.If the Gap/Mark Sensor selection is incorrect change using the “Left” or “Right” Key, then press the Enter key to Save.(Gap or Mark are used most frequently selection)Press the Down ↓ Arrow key until the display reads “Run Auto Cal/to Run Press “.  Please Press the Enter key to run.When completed the display will read “Sensed Distance X.XX” (e.g. 2.11 inches).Confirm that the Sensed Distance is correct.(The Sensed Distance is measured from the top of one label to the top of the next label, includes the gap)If the Sensed Distance is incorrect then re-load the media and run the run Auto Cal again.If the sensed Distance is still incorrect then contact Printronix Technical Support.Press the “Menu”  Key until the display reads “Configuration” and then Press Enter. Press the Down ↓ Arrow Key until the display reads “Save Config.”Please select the desired Config number (1-8 Possible Configurations), Press the Enter Key to save.Press the Down ↓ Arrow Key until the display reads “Power-Up Config.”If the Power-Up Config number matches the Save Config number then Press the Enter Key to save.If the Power-Up Config number does not match the Save Config number then using the “Left” Or “Right” key, then Press the Enter key to save.Power Off the printer, wait 30 seconds, then power the printer back on.Print the internal checkerboard testIf the checkerboard pattern prints correctly and does not print in the gap then print your label job again and confirm it prints correctly.If you have confirmed that your printer driver is correct, but your label still prints incorrectly then contact your Label Software Manufacturer.

Corrupted NVRam due to an electrical disturbance (T4M,SL4M)Product: SL/T4MSymptomCorrupted NVRam due to an electrical disturbanceRecommend SolutionClear the NVRam. This returns the printer to its Factory default state.Note: This procedure erases any stored configurations. If possible, print a configuration before performing this procedure.Turn the printer off. Hold down the [left button]+[bottom button] keys at the same time, and turn the printer on. Hold down the buttons for 10-15seconds, then release.When the LCD displays;BOOT DIAGNOSTICSPRESS ENTERPress [Enter]Press [bottom button] until MISCELLANEOUS TOOLS is highlighted.Press [Enter]Press [bottom button] until ERASE ALL NVRAM is highlighted.Press [Enter]Turn the printer off, wait about 10-15 seconds, turn the printer back on.Reload any configuration information.

Problem configuring the Wireless parametersProduct: SL/T4M Thermal PrinterSymptomProblem configuring the Wireless parameters because the SL/T4M does not have dual nic capability.Recommend SolutionUse a PTX Setup file to configure the ethernet parameters.Below is an example script;*******************************************************Edit this example script below for your site. Copy the script to the printer’s parallel port in normal Online mode.Example: >copy/b filename.ext lpt1:All nic commands are listed in the PrintNet User manual.—- remove this header before sending to the printer —-!PTX_SETUPNIC_SETUPstore tcpip 2 opts -rarp -bootp dhcpstore tcpip tcp rxwin 4096store tcpip tcp opts -keepalivestore ifc 2 wlan profile 6store ifc 2 wlan auth openstore ifc 2 wlan ssid YourSSIDstore ifc 2 wlan key 1 D1C2-B3A4-9586-7768-594A-3B2C-1Dstore ifc 2 wlan defkey 1store pping opts enablestore pping period 2store pping packet 2set sysinfo module -netbiossaveresetEND_NIC_SETUPPTX_END******************************************

How do I set the IP address on my printer?Product: SL/T5000rSymptomHow do I set the IP address on my printer?Recommend SolutionThe PrintNet IP address settings are set from the printer control panel.You can set three IP parameters from the printer control panel. The available parameters are:IP AddressSubnet MaskGateway (optional)The procedure for changing any of the parameters is the same. The procedure for changing the IP Address is given here as an example. Use the same procedure for the other IP parameters.Make sure the printer is on and paper/ribbon is loaded.Press the PAUSE key to place the printer in the OFFLINE mode.Unlock the Front Panel. (DOWN Arrow + ENTER keys at the same time.)Press the MENU key until the LCD displays “ETHERNET ADDRESS.”Press the DOWN arrow key to access the first segment of the IP address to be changed. (Or press DOWN arrow again to scroll through the Subnet and Gateway segments.)Press the + (plus) or – (minus) keys to change the segment.Press ENTER to make the selection. An asterisk appears to the right of the value.If other IP address segments need to be changed, go to step 5.When Finished the [Pause] key twice to go ONLINE. This burns the IP information into the printer.The ethernet configuration is global to the printer, and takes effect immediately.

Not all the front panel menus are displayed (SL5,T5)Product: SL/T5000rSymptomNot all the front panel menus are displayed.Possible CauseThe ‘Admin User’ menu is disabled.Recommend SolutionEnable the ‘Admin User’ menu. From the front panel unlock the front panel by pressing the [Enter key]+[down arrow key], at the same time. Press the menu key until “Printer Control” is displayed. Press the [up arrow] until “Admin User” is displayed. Press the [right arrow] until “Enabled” is displayed, and press the [Enter key]. You can make the change permanent by saving the configuration under the “Configuration Control” menu, or you will be given the opportunity to save the setting when you put the printer back online.

Not all the front panel menus are displayed (SL4,T4M)Product: SL/T4MSymptomNot all the front panel menus are displayedPossible CauseThe ‘Admin User’ menu is disabled.Recommend SolutionEnable the ‘Admin User’ menu. Unlock the front panel by pressing the [Enter key]+[down button], at the same time. Navigate to the “Printer Setup” menu, press [Enter], and press the [up button] until “Admin User” is displayed. Press the [right button] until “Enabled” is displayed, and press the [Enter key]. You will be given the opportunity to save the setting when you put the printer back online.

My barcode looks good but it has a failing gradeProduct: SV100/SV200SymptomMy barcode looks good but it has a failing gradePossible CauseDefects in the barcode printing processRecommend SolutionThe SV (ANSI) Parameters define the overall grade for a barcode. The lowest grade of all the parameters defines the Overall Grade for the barcode. Even though a barcode may appear to be of good quality to the human eye, many times if we examine it more closely we will find previously undetected defects. Below is a brief list of some of the possible defects and causes for a Typical Thermal printer.SV 100/200 Validator parameters.Low Decodability GradeIf avg. bar deviation is good, then there could be a failed print head element on the side of one of the bars in the code when codes are printed in picket fence orientation.If avg. bar deviation is too + or -, then the heat setting may not be correct. Too far + means too high of heat.Print head may be dirty, causing ribbon “smudge”Bad barcode layout (usually created by graphics command rather than the printer language barcode command)SV mounted at wrong distance – therefore out of focus. (This can be checked by ensuring the X dimension analysis matches the code’s X dimension. If X is correct, focus is not the problem.)Low Defects GradeA failed print head element is located inside a bar of the code (white stripe) when codes are printed in picket fence orientation.Dirty print head or “smudge”Rough edges on the bars of codes printed in ladder orientation“Rough” textured or metallic type mediaLow Print ContrastDark or specular (shiny) mediaDirect thermal media not compatible with 660 nm wavelength – bars are not low reflectanceNo read ConditionRibbon wrinkleFailed print head element(s) large enough to cause enough damage to make the barcode un-decodablePrint speed too fast for SV scan rateMultiple ReadsDamaged code where SV finds the code, loses the code, and then senses it again. (This can be diagnosed with number of scans.) Damage can occur with ribbon wrinkle, ribbon/media mismatch, “hole” in the ribbon, too low heat setting, etc.SV gain and offset adjustment not optimum for robust reading of the particular mediaGeneral CommentsThe best quality is achieved with the most minus avg. bar deviation that creates the maximum Decodability calculationModulation can be adversely affected by out of focus – see Decodability e. aboveParameters like Modulation and Rmin/Rmax are more media dependent or beam size vs. X dimension dependent. Therefore these may not be good indications of printer performance.

No Applicator Mode 6 in Zebra XiIII Plus MenuProduct: SV100/SV200SymptomNo Applicator Mode 6 in Zebra XiIII Plus MenuPossible CauseFirmware Has Not Been DownloadedRecommend SolutionZebra XiIII Plus Firmware Installation ProcedureNOTE: Print a copy of these instructions and refer to it during the firmware installation.System requirements: WINDOWS or DOS based P.C. 3 MBytes free hard drive spaceImportant:The file must be uploaded to the printer through a copying method that does not add to or alter the ASCII file in any way!This process will overwrite the earlier software version currently installed in your printer.Preparing the Printer for Upload:For Printer currently with Firmware V60.XX.XX:Do not hold the + / – or < / > (black oval) buttons while powering up as you may have been instructed to do with previous versions of firmware. If you hold these buttons during power up and enter the powerdownload mode, the upgrade may be unsuccessful.For Printer currently with Firmware V4X.XX.XX (pre- V60):With the power turned OFF, press and hold the two black oval buttons located directly under the LCD while powering ON the printer. When the PAUSE LED comes on, release the buttons.This will set the printer into download mode.*Note: The LCD display will be blank at first – this is normal. You will see status messages displayed once the files begins to load within the printer.Directions for uploading from the Windows environment:Save the file (SPxxxx.ZPL) to an appropriate working directory on the hard drive (the root C: drive may be easiest).Open a Command Prompt Window (Go to RUN…, type “command” – do not use “cmd” it is not the same thing) and change to the directory containing the SPxxxx.ZPL file.Copy the file (SPxxxx.ZPL) directly to the printer:• Instructions below include examples for Parallel, Network or Serial (slowest option) downloadoptions.• USB is considered a “virtual port” only supported within Windows; and is, therefore, not asupported download method.Parallel: To send file through the parallel port, type: COPY SPxxxx.ZPL LPT1 then press Enter.Serial: To send the file though a com port, COM1 for example, you need to set the communicationsparameters on the port first, then copy the file:At the prompt, type: MODE COM1 57600,N,8,1,X then press Enter. (where “57600” is the baud rate.This can also be whatever value matches the printer’s current settings: 19200, 9600, etc).Type: COPY SPxxxx.ZPL COM1 then press Enter.Once the firmware has been uploaded to the printer, the printer will reset. A configuration label will usually print automatically (if not, print one manually by holding in the ‘Cancel’ button for 6 or 7 seconds as you turn the power on). Confirm that the firmware version on the label matches the version downloaded.Network: To send file through a network connection via FTP File Transfer Protocol from DOS:Prepare the printer as described in the first step on the first page and copy the file to the desired directory location.Go to a Command prompt and change to the directory where the firmware file is stored.From the Command prompt Type: ftp Press again.You will then see the FTP prompt: FTP>Type: put < spxxxx.zpl > The file is now sent to its destination.Example: put spxxxx.zpl Note: FTP is case sensitive, use lower case…

No Applicator Mode 6 in Zebra XiIII MenuProduct: SV100/SV200SymptomNo Applicator Mode 6 in Zebra XiIII MenuPossible CauseFirmware Has Not Been DownloadedRecommend SolutionZebra XiIII Firmware Installation ProcedureNOTE: Print a copy of these instructions and refer to it during the firmware installation.System requirements: WINDOWS or DOS based P.C. 3 MBytes free hard drive spaceImportant:The file must be uploaded to the printer through a copying method that does not add to or alter the ASCII file in any way!This process will overwrite the earlier software version currently installed in your printer.Preparing the Printer for Upload:With the power turned OFF, press and hold the two black oval buttons located directly under the LCD while powering ON the printer. When the PAUSE LED comes on, release the buttons.This will set the printer into download mode.*Note: The LCD display will be blank at first – this is normal. You will see status messages displayed once the files begins to load within the printer.Directions for uploading from the Windows environment:Save the file (SPxxxx.ZPL) to an appropriate working directory on the hard drive (the root C: drive may be easiest).Open a Command Prompt Window (Go to RUN…, type “command” – do not use “cmd” it is not the same thing) and change to the directory containing the SPxxxx.ZPL file.Copy the file (SPxxxx.ZPL) directly to the printer:**Instructions below include examples for Parallel, Network or Serial (slowest option) download options.Parallel: To send file through the parallel port, type: COPY SPxxxx.ZPL LPT1 then press Enter.Serial: To send the file though a com port, COM1 for example, you need to set the communications parameters on the port first, then copy the file:At the prompt, type: MODE COM1 57600,N,8,1,X then press Enter. (where “57600” is the baud rate.This can also be whatever value matches the printer’s current settings: 19200, 9600, etc).Type: COPY SPxxxx.ZPL COM1 then press Enter.Once the firmware has been uploaded to the printer, the printer will reset. A configuration label will usually print automatically (if not, print one manually by holding in the ‘Cancel’ button for 6 or 7 seconds as you turn the power on). Confirm that the firmware version on the label matches the version downloaded.Network: To send file through a network connection via FTP File Transfer Protocol from DOS:Prepare the printer as described in the first step on the first page and copy the file to the desired directory location.Go to a Command prompt and change to the directory where the firmware file is stored.From the Command prompt Type: ftp Press again.You will then see the FTP prompt: FTP>Type: put < spxxxx.zpl > The file is now sent to its destination.Example: put spxxxx.zpl Note: FTP is case sensitive, use lower case.

Using PrintNet Enterprise to transfer data files for printingProduct: All, PrintNet EnterpriseSymptomHow can PrintNet Enterprise be used to transfer data files for printing?Possible CauseUse the macro facility of PrintNet Enterprise to send data files to the printer to be printed.IMPORTANT: This is not the way to download flash files or program files.Recommend SolutionThe macro feature of PrintNet Enterprise Suite can be used to print a data file by sending the file over Ethernet or serial COM1 to a printer.In the ‘File’ menu, select ‘Preferences’.In the Preferences window that pops up, select the ‘Macro Setting’ tab.If using Ethernet:On the ‘Macro Setting’ tab, on the ‘General’ subtab, set ‘Printer Port’ to “Network”Check the box labeled “Use selected network printer”or on the ‘Network’ subtab fill in the Ethernet address to always use.If using serial:On the ‘Macro Setting’ tab, on the ‘General’ subtab, set ‘Printer Port’ to “COM1″On the ‘Serial’ subtab, set the serial properties.Click “OK”.To set up a file to print:Select your printer.Open the menu ‘Utilities’Select ‘Macro Utility’.On one of the macro lines, press the button labeled ‘Configure’.In the window that pops up:Check ‘Print from file’Press the ‘Browse’ button.Browse and select your file to print.Click “OK”.Note that the button labeled with a macro number changes to display the file name.To print the file, press the button displaying the file name.If you save the PNE configuration, the macro menu will be set up for you for next time.img-3

TCP-IP printing from (Open) VMSProduct: PrintNet ALLSymptomTCP/IP printing from (Open) VMSRecommend SolutionUse TELNETSYM for printing.(Note: Do not use DCPS as it requires a Postscript printer).The setup of the queue should be:INIT/QUEUE name /ON=vmsnode::”ip-addr:9100″ /PROCESSOR=UCX$TELNETSYM /STARTWhere ip-addr is the IP address of the printer, and 9100 is the port number.Sometimes there is a need to change the ucx$telnetsym to an 8-bit clean raw TCP type connection with the command:DEFINE /SYSTEM UCX$TELNETSYM_RAW_TCP 1Sometimes the print queue stalls if the job is spooled for more than 3 minutes.To resolve this problem put the VMS commands:DEFINE/SYSTEM/NOLOG UCX$TELNETSYM_IDLE_TIMEOUT “0 00:00:15.00”DEFINE/SYSTEM/NOLOG UCX$TELNETSYM_RETRY_INTERVAL “0 00:00:30.00″into the VMS host’s startup file. This command can also be typed in at the VMS prompt to set the retry interval without having to reboot the host.If using TCPIP V5 or greater, the following also works;$ init -/que queue_name -/on=VMSnode::”ip-addr:9100” -/process=TCPIP$TELNETSYM -/start$!

Tru64 Unix TCP-IP Network Printing using socket connectionProduct: P7000, SL/T5000, SL/T4M with PrintNetSymptomTru64 Unix TCP/IP Network Printing using socket connectionRecommend SolutionThe PrintNet adapter uses port 9100.Requires Tru64 UNIX V4.0a or later.Example printcap file:lp|lp0|0::ct=tcp::af=/usr/adm/lpacct::if=/usr/lbin/printfilter::lf=/usr/adm/lp0err::lp=@printer_ip_name/port_9100::mx#0::of=/usr/lbin/printfilter::pl#66::pw#80::rw::sd=/usr/spool/lpd0::xf=/usr/lbin/xf:Replace /usr/lbin/printfilter with the appropriate print filter. Compaq recommends the Generic filter.The printer_ip_name is the printer name in the etc/hosts file or the IP address of the printer.The /etc/services file must be updated to include the printer port/socket number. In this example the printer uses port 9100 so the following /etc/services entry was added.port_9100 9100/tcpImportant: The name port_9100 is user definable. If a 9100/tcp entry exists, use the name previously defined. Don’t create a second entry. The port number is printer specific. The PrintNet

Configuring a printer on a Tandem host via TCPIPProduct: P7000, SL/T5000, SL/T4M with PrintNetSymptomConfiguring a printer on a Tandem host via TCPIP.Recommend SolutionTandem systems support LPR printing via TCP/IP. Below is an example setup.In the example below, the most important parts are the PORT and the QUEUENAME fields. The PORTmust equal 515, which is the LPR port, and the QUEUENAME must equal a destination on the PrintNetadapter. DEVICE$PSMMS02CONTYPE=TCP/IPADDRESS=xxx.xxx.xxx.xxxPORT=515TCP/IP-A=$ZTC4PROTOCOL=LPD1179TIMEOUT=60000DEVTYPE=LU1QUEUENAME=d1prnDEVICE:$PSMMS02STATE:OFF LINELAST ERROR:%004214EXCLUSIVE:ONFIFO:ONHEADER:OFFTRUNCATION:OFFDRAINING:NOPRINTING JOB:NONEPARM:1024 (%2000)PROCESS:$LPTC4RETRY:5TIMEOUT:-1SPEED:100WIDTH:-1FORM:RESTART: 60DEVRESET:OFFDEVTYPE:STARTOFF:OFFENDFF:OFFCHARMAP:NONEPREXLATE:OFFLUTOFVALUE:CRFFCRLUEOVALUE:CRLFLUEOLWHEN:LT132LOCATIONFLAGS DEVICEFONT#B05MMS.DEFAULT$PSMMS02

Configuring Email alertsProduct: ALL with PrintNetSymptomConfiguring Email alertsRecommend SolutionPower on the printer.Type in “telnet ” and press enter.Type in as username “root” and press 2 × enter.Type in “set logpath l1 port email” and press enter.Type in “set dest d1prn logpath l1” and press enter.Type in “set sysinfo email @” and press enter. is the name before the @ sign for example xyzuser@printronixautoid.com then the username isxyzuser. is the ipaddress of the mail server that can handle SMTP mail.Type in “set logpath l1 type job user ioport cksum printer” and press enter.job : this will sent regarding job ID, username, etcuser : user ID with three messages per job about start and finishcksum : 16-bit checksum value to confirm integrity of data printedprinter : for special printer feedbackioport : printer error messages determined through the parallel port pinsType in “save” and press enter.Type in “reset” and press enter.

Last page does not eject from printerProduct: PrintNetSymptomLast page does not eject from printer, and interface is Ethernet using the PrintNet adapter.Possible CauseJob could be missing a final ‘form feed’ command.Recommend SolutionAdd a form feed using the ‘trailer’ feature.The PrintNet adapter has eight data ports, 9100 through 9107.Each port has a “destination” (or “queue”), and each destination has a “model”.By default, port 9100 is assigned destination/queue name “d1prn” and model “m1”.The model defines how the print job will be processed as it passes through to the printer.Models are a set of filters that can be used to modify the print data stream.The model can be assigned a “trailer” consisting of a form feed. When the Ethernet port closes, a form feed will be issued and the print job will eject paper to the next top-of-form.It is easy to assign a form feed with a web browser. Using telnet, a complex string of hex bytes or variables can be programmed and documented.METHOD 1 – browser:Log into the NIC using a web browser. The web address is the IP of the NIC.Select ‘Configuration’ and log in.The user name is ‘root’, without the quotes, in lower case.The password is blank; just ignore the field.Select ‘Print Model’.Verify the model (“m1” is the default model for port 9100)Pick the ‘formfeed’ trailer from the pull-down list.NOTE: Erase the trailer by setting all trailer values to NULL at this point.Press the ‘Submit’ button at the bottom of the page.Select ‘System’ menu function at the top of the page.Press ‘Reboot’ button. Indicate that you are sure by pressing ‘Yes’.METHOD 2 – telnet:[Note: Type the values in single quotes, not the quotes themselves, and press Enter.]Open a telnet session with the NIC.Open a DOS window (cmd.com) and/or run telnet using the IP address of the NIC.Login name is ‘root’ in lower case, password is empty (Enter key only).To see the current trailer for model m1, type ‘list model m1’.To set a trailer of “form feed” for model m1, type ‘set model m1 trailer 0x0c’0x0c is the numerial value of a form feed character”Form feed” is also pre-defined as variable $FF, so you could type ‘set model m1trailer $FF’To clear the trailer for m1, type ‘set model m1 trailer’After making all changes, type ‘save’ then type ‘reset’.The NIC will reset and the printer will cycle power.

Migrate flash files between printersProduct: ALL PrintNetSymptomMigrate flash files between printers. Flash file can contain TrueType font, stored form, CST, etc.Possible CauseUse Printnet Enterprise Suite, v3.12D or later.Recommend SolutionYou may wish to transfer some stored files between printers, such as TrueType fonts, stored forms or a CST bundle. The files to be transferred must be compatible with the destination printer.In order to transfer the files, use the Flash File Manager feature of PrintNet Enterprise Suite. Collect the file or files from the source printer, and save into a file that is stored on the PC running PrintNet Enterprise Suite. Then the saved file can be copied to one or more printers using PrintNet Enterprise Suite.In PrintNet Enterprise Suite, select the ‘from’ printer having the desired files.In the ‘Applications’ menu, open ‘Flash File Manager’, and press the ‘Get File Info’ button.Mark all the files to save, by using Ctrl-left-click with the mouse.Press the ‘Upload’ button to upload the files to the host PC.Press the ‘Save As’ button to give a filename to the saved set of files from the printer. Make sure the file has an extension of PFF.Close the ‘Flash File Manager’ window.Attach a Download icon to the ‘to’ printer that will be getting the files.Double click the Download icon and browse to the saved flash file with the extension PFF located on the PC running  PrintNet Enterprise Suite. Close the Download icon window.Select the ‘to’ printer.In the ‘Applications menu’, open ‘File Download’.Verify that the ‘Flash Files’ file-type box is the only one checked.Press the ‘Start’ button to start the download.Close the ‘File Download’ window when the operation is complete.Check printer contents by accessing the ‘Flash File Manager’ window or the Stored FileList section of the configuration on the destination printer.

Need to switch emulationsProduct: PrintNetSymptomNeed to switch emulations, and interface is Ethernet using the PrintNet adapter.Recommend SolutionSave multiple configurations, each with its own emulation. Then assign eachconfiguration to one of the ‘print models’ in the PrintNet adapter.The PrintNet adapter has eight data “ports”, 9100 through 9107.Each port has a “destination” (or “queue”), and each destination has a “model”.By default, port 9100 is assigned destination/queue name “d1prn” and model “m1”.The model defines how the print job will be processed as it passes through to the printer.Models are a set of filters that can be used to modify the print data stream.The model can be assigned one of the eight saved configurations “1” through “8”, or the factory configuration, represented by “0”. When a job comes in on the port to which that model is assigned, the appropriate configuration is loaded before printing starts. Any config can be assigned to any model.For example, save a PGL configuration as #1 and a ZGL configuration as #2.Then set model m1 with config 1, and set model m2 with config 2.Then, when the user prints to IP:9100 or prints to destination d1prn, config 1 will load and the printer will be configured for PGL.On the other hand, when the user prints to IP:9101 or to destination d2prn, config 2 will load and the printer will be in ZGL mode.METHOD 1 – browser:Log into the NIC using a web browser. The web address is the IP of the NIC.Select ‘Configuration’ and log in.The user name is ‘root’, without the quotes, in lower case.The password is blank; just ignore the field.Select ‘Print Model’.Verify the model (“m1” is the default model for port 9100)Pick the Configuration Number from the pull-down list.Allowable values are 1-8, Factory, (None)Press the ‘Submit’ button at the bottom of the page.Select ‘System’ menu function at the top the of page.Press ‘Reboot’ button. Indicate that you are sure by pressing ‘Yes’.METHOD 2 – telnet:[Note: Type the values in single quotes, not the quotes themselves, and press Enter.]Open a telnet session with the NIC.Open a DOS window (cmd.com) and/or run telnet using the IP address of the NIC.Login name is ‘root’ in lower case, password is empty (Enter key only).To see the current config for model m1, type ‘list model m1’.To set model m1 to config #1, type ‘set model m1 config 1’There is no space in “m1” but there is a space in “config 1″To set model m1 to config #4, type ‘set model m1 config 4’Do not load a configuration that has not been saved yet!To set model m1 to the factory config, type ‘set model m1 config 0’To clear the config for m1, type ‘set model m1 config’After making all changes, type ‘save’ then type ‘reset’.The NIC will reset and the printer will cycle power.

How to capture an electronic job fileProduct: AllSymptomHow to capture an electronic job file using PrintNet Enterprise SuitePossible CauseWhen the user wants to troubleshoot a problem and cannot generate an electronic job file in another way, such as from a mini/mainframe environmentRecommend SolutionStart PrintNet Enterprise Suite version 3.12D or greater.Select the printer by right-clicking on its name in the database window.Select the menu ‘Applications’.In ‘Applications’, select ‘Job Capture’.|A message box should appear, saying “Connecting to printer”If you fail to connect, check the value of ‘Debug Port’ or ‘PNE Port’, which must be set to “Ethernet”.When the Job Capture window pops up:Optionally, select menu ‘Options’, and disable printing. The printer will accept the job so the capture will take place, but no printing will occur.Select menu ‘Capture’ and select ‘Data From’. Pick the interface over which the data is entering the printer.Select ‘Start’ from the ‘Capture’ menu. An information block on the status bar along the bottom of the window reads “Capture: On”, then “Capture: Idle”.When a job is sent to the printer, the number of bytes received is accumulated in the status bar, but the data contents are not displayed in real-time.When the capture is stopped, by using ‘Capture’ menu and ‘Stop’, the accumulated data contents are displayed. The file can be saved using the ‘File’ menu.

How to capture an electronic configuration listingProduct: AllSymptomHow to capture an electronic configuration listing using PrintNet Enterprise SuitePossible CauseWhen an electronic copy of a configuration listing is desired, or it is necessary to get the configuration remotely.Recommend SolutionStart PrintNet Enterprise Suite version 3.12D or greater.Select the printer by right-clicking on its name in the database window.Select the menu ‘Applications’.In ‘Applications’, select ‘Information Capture’.A message box should appear, saying “Connecting to printer”If you fail to connect, check the value of ‘Debug Port’ or ‘PNE Port’, which must be set to “Ethernet”.When the Information Capture window pops up:Select menu ‘Configuration Printout’Select ‘Current’, or the desired configuration to capture.Select menu ‘File’ and select ‘Save As’ to save the configuration as a text file, or capture part or all of the text with a mouse and copy it into a word processor such as Notepad.NOTE: PrintNet Enterprise doesn’t save line feeds, just carriage returns, so the text runs together in the output file. To save the files with line feeds, on a Windows system and Word 2003, do the following:Select the menu ‘File’, and select ‘Save As’ from the ‘File’ menu.Name the file with an extension of .TXTOpen the saved file in Word as an MS-DOS type.Save the file as an MS-DOS type, and check the box that says “Insert Line Breaks”

Wireless troubleshooting using the E-Net test page.Product: Wireless PrintNet ALLSymptomWireless troubleshooting using the E-Net test page.Recommend SolutionPrint the E-Net test page.(P7000) Front Panel -> DIAGNOSTICS -> Printer Tests -> Ethernet Test -> Enter(SL/T5000r) Front Panel -> Test Print -> Ethernet Test -> Enter(SL/T4M) Front Panel -> DIAGNOSTICS -> Printer Tests -> Ethernet Test -> EnterA. Quality (Signal Strength) = 0%This indicates that the radio card is not communicating with the Access Point (AP).SSID incorrect. (The SSID is case sensitive)Encryption is not enabled.Missing/loose radio card. (Check the driver listed in the E-Net test page)Antenna connection in wrong position (LA-5137 radio)Wrong IP address, or dhcp should be enabled.Register the MAC address in the AP’s MAC access table. (only if the AP is using a MAC table)Defective radio card.Defective Antenna.Defective PrintNet assy.B. Quality > 1-100%, Status = dis-associated.This indicates that the radio card is communicating with the access point, but has not yet been authenticated by the AP.Wrong WEP key (if using WEP encryption)WEP default key not selected (if using WEP encryption)WPA mode disabled. (if using TKIP/AES cipher)WPA Cipher incorrect. (TKIP/AES cipher only)Wrong passphrase (TKIP/AES cipher only)Wrong Authentication method. (open/shared)Radio card, or printer software, does not support the type of encryption that is used on the AP.C. Quality > 1-100%, Status = associated, but cannot ping the device.This indicates that the radio card is communicating with the access point, and has been authenticated by the AP, but an additional layer of security is implemented.Register the MAC address in the AP’s MAC access table. (only if the AP is using a MAC table)Register the device on the RADIUS server (only if using a radius server).Add the device to the list of approved devices on the network Switches/Routers. (rare)Increase the negotiation timeout on the AP (Cisco).Do not connect the wired adapter to the network (Dual nic installation only)

AIX Print jobs restart or queue goes down.Product: PrintNet ALLSymptomAIX Print jobs restart or queue goes down.Possible CauseThe default remote queue timeout setting is too low.Recommend SolutionIf the queue is set up for “standard processing”, (not local filtering),add a -T50 flag to rembak in the queue device stanza for thequeue in /etc/qconfigbackend = /usr/lib/lpd/rembak -T50If the queue was set up for local filtering edit the file/usr/lib/lpd/pio/etc/piorlfb and change the line;typeset piorlfb_rbflags=””totypeset piorlfb_rbflags=”-T50″

I forgot my PrintNet login passwordProduct: PrintNet ALLSymptomI forgot my PrintNet login password.Possible CauseOccasionally a user will set a ‘root’ user password on the PrintNet adapter, and then forget it.Recommend SolutionP7000 series printer.Turn the printer ON, Go [offline], and unlock the front panel (up and down arrow keys at the same time, release).Press all four arrow keys (up, down, prev, next) at the same time, and release.Right arrow to “PRINTER MGMT”.Down arrow, and then right arrow to “E-NET to DEFAULT”.Press [enter].Re-program the IP address information from the front panel. Unfortunately steps 1-5 also clears the IP address information and sets the adapter back to factory defaults.SL/T5000”r” series printer.Turn the printer ON, Go [offline], and unlock the front panel (up and down arrow keys at the same time, release).Press all four key [Job Select]+[Feed]+[Test Print]+[Cancel] at the same time, and release.Down arrow to “E-NET to DEFAULT”.Press [Enter].Re-program the IP address information from the front panel. Unfortunately steps 1-4 also clears the IP address information and sets the adapter back to factory defaults.SL/T4M series printer.Turn the printer ON, Go [offline], and unlock the front panel, [Down button] + [Enter] keys at the same time, release.Press all four button keys at the same time, and release.Down button to “E-NET to DEFAULT”.Press [Enter].Re-program the IP address information from the front panel. Unfortunately steps 1-4 also clears the IP address information and sets the adapter back to factory defaults.

TCP Port Busy error messageProduct: PrintNet ALLSymptom”TCP Port Busy” error message. Cannot access the printer via the PrintNet Enterprise Software.Possible CauseThe Printer needs to have the “PNE Port” option set to “Ethernet”.Recommend SolutionEnable the PNE Port on the printer.SL5000r/T5000r series:Unlock the front panel, and press the menu key until PRINTER MGMT is displayed. Press the [down arrow] key until “PNE Port” is displayed. Press the [right arrow] key until “Ethernet*” is displayed, press [Enter]. This change is global to the printer, andtakes effect immediately.P7000 series printer:Unlock the front panel, and press the [right arrow] key until PRINTER MGMT is displayed. Press the [down arrow] key until “PNE Port” is displayed. Press the [right arrow] key until “Ethernet*” is displayed, press [Enter]. This change is global to theprinter, and takes effect immediately.SL4M, T4M:First ‘Enable’ “Admin User” under the PRINTER SETUP front panel menu. Under the INTERFACES menu, go to sub-menu ‘Printer Mgmt’, and press [Enter]. Set the PNE Port = Ethernet*. This change is global to the printer, and takes effect immediately.